How to Change Main Panel Battery

Power down the panel – to do this unplug the transformer from wall (should be plugged into an electrical outlet near keypad) Open the panel by removing front casing by lightly pulling up on it.

Then on the top/front of the keypad there will be two tabs that need to be opened by lifting on them. This will release the front face of the keypad. Slowly pull the front of the keypad away from the back-wall plate. Unclip the battery & remove the battery.

Replace new battery & reattach lead.

Close the front of the keypad & reattach casing.

Plug transformer back into the wall to power up panel.

GE Wireless Door Contact (60-362N-10-319.5)

Battery: One 3 Volt Lithium.  Use a CR123A style.

To Open Device: Squeeze short sides of contact in & pull away from wall.

GE Allegro Wireless Door Contact (60-670-95R)

Battery: 2 x Lithium AAA

To Open Device: Press button on short end of contact & lift cover away from the wall.

GE Allegro Wireless Glassbreak Detector (60-873-95)

Battery: One 3 Volt Lithium.  Use a CR123A style

To Open Device: Wiggle & pull straight off.

GE Allegro Wireless Pet Immune Detector (60-807-95R)

Battery: 2 Lithium AA

To Open Device: Depress tab on top of motion detector & pull away from wall.  Depress 3 tabs using thumb & fingers. Pull front of motion away from backing.

GE Wireless Smoke Detector (GEC-TX6010011)

Battery: Two 3 Volt Lithium.  Use a CR123A style.

To Open Device: Twist counter clockwise & pull off. To replace, line up arrows on base with raised bump on side of detector & turn clockwise.

GE Wireless 4 Button Keyfob (60-659-95R)

Battery: One flat “coin” style Lithium CR2032

To Open Device: Pull apart or use flat screwdriver to lightly separate casing.  Remove circuit board & slide out battery.

To stop the trouble beeps arm then disarm the system while the trouble condition exists. Trouble beeps will resume 4 hours later unless the trouble condition is corrected.

AC power failure -This condition (if programmed by the installer) occurs if your security system has been accidentally unplugged or if there has been an AC power outage. The icon will appear in the top left corner of the screen display, and trouble beeps start after 5 minutes. If AC power is not restored within a programmed period of time (5 to 254 minutes), the system will call the central monitoring station. The backup battery, if fully charged, will last for 18 to 24 hours (depending on the load applied to the panel) with no AC power.

System battery failure – This condition occurs if the emergency backup battery has failed. Trouble beeps will start and the icon will appear in the top left corner of the STATUS & SETTINGS screen. If your AC power is not working, your security system will shut down once the battery has failed. If the condition does not clear after AC power has been restored and 24 hours have passed, call your security system dealer.

Restoration of power -This condition occurs after a complete loss of power (AC and battery). When power is restored, the panel will return to the arming state with the same zones bypassed it had prior to losing power.

Sensor failure – This condition occurs if a sensor is not communicating with the panel. Trouble beeps will start. You may need to call your security system dealer if the problem continues.

Sensor low battery – This condition occurs if a system sensor has a low battery. The sensor may still be communicating with the panel. Trouble beeps will start. Press and then press in the STATUS & SETTINGS menu.

The panel will speak which sensors have low battery. You may need to call your security system dealer to resolve this problem. Some sensor batteries can be replaced by the homeowner.

Failure to communicate -This condition occurs if your security system could not communicate successfully to the central monitoring station. Your system will try to report to the central monitoring station eight times before it tells you there is a fail-to-communicate problem. Trouble beeps will start and the yellow triangle appears over the settings icon. You may need to call your security system dealer if the problem continues.

Sensor open- This condition occurs if a door or window is open or a system sensor has been disturbed and not reset properly. For example, a door/window sensor magnet may have been removed from the sensor. Your system will indicate this condition to you by displaying a red SENSOR OPEN icon and show the icon in the bottom right of the main screen. Correct the problem by resetting the sensor. If this condition continues, call your security system dealer.

Sensor tampered – This condition occurs when a sensor is physically tampered with, for example, that the cover is taken off one of the sensors. If the system is armed, an alarm will occur. Sensor icons change to red icon appears, and the red alarm pop-up will appear if the system is armed. Trouble beeps will start. Correct the problem by resetting the sensor. If this condition continues, call your security system dealer.

RF jam detected – The panel receiver may be experiencing some interference. The system will call to notify the central monitoring station about this problem.

Clearing status Some types of status conditions, such as alarm history, must be cleared manually. To clear system status, press CLEAR next to Panel Status in the STATUS & SETTINGS menu. If the trouble condition was a low system battery, perform a sensor test. The should disappear if all trouble conditions have been corrected.

When a smoke detector goes off, disarm the system to silence the siren, wireless smoke sensors reset automatically once they are clear of smoke

1. Prior to testing, ensure your system is disarmed and Ready light is On.

2. If there are any open zones you must secure them before you start.

3. Before you start don’t forget to call our monitoring station (1-855-488-3777) to put your system on test. Quick Tip – Before calling the monitoring station please have ready your verbal passcode & your account number as well. If you are unsure of your account number call our office 403-343-1122.

4. Arm your system in away mode and once the countdown stops; start opening windows and doors, walk in front of the motion detectors if you have glass breaks clap your hand close to it and make it as loud as you can.

5. Once you have completed all your zones turn off your alarm system and call back the monitoring station to see if they received your signals.

Should the system fail to function properly, call us 1-403-343-1122 immediately for service

1. Enter the Status & Settings menu and scroll to the Chime option.

2. Press On or Off to modify the setting (a gold icon indicates the option is selected).

3. Press Close to exit the Status & Settings menu.

Bypassing a sensor allows you to open the sensor while the system is armed. For example, if your doors and windows are armed and you want to open your kitchen window, but do not want to disarm the entire system, you can bypass the kitchen window sensor and then open the kitchen window without causing an alarm. Bypassed sensors are automatically un bypassed when the arming level is changed to a level where the sensor is not active.

To bypass, or unbypass, a sensor:
1. Press the gear cog.
2. Press SELECT
3. Enter your master code.
4. Next to the sensor name, select bypassed to bypass the selected sensor, or not bypassed to not bypass the selected sensor.

To stop the trouble beeps, press and then press the icon or arm then disarm the system while the trouble condition exists. Trouble beeps will resume 4 hours later unless the trouble condition is corrected.

To disarm (level 1):

1. Press PRESS TO DISARM.

2. Enter your code when the keypad screen appears.

The panel displays and speaks Disarmed and the panel beeps once.

To arm doors and windows (level 2):

1. Ensure that all doors and windows are closed.

2. Press – press to arm

3. Press DOORS & WINDOWS ONLY (STAY)

4. If a code is required, enter your code when the keypad screen appears.

The panel speaks Doors and Windows On and starts an exit delay, and sounds exit beeps in groups of two until the exit delay expires. To cancel arming press CANCEL ARMING on the countdown screen.

To arm motion sensors (level 3):

1. Press – press to arm

2. Press MOTION SENSORS ONLY (AWAY) (see

3. If a code is required, enter your code when the keypad screen appears.

The panel speaks Motions On, starts an exit delay, and sounds exit beeps in

groups of three until the exit delay expires.

Note: Depending on your configuration, this option may not appear.

To arm doors, windows, and motion sensors (level 4):

1. Press – press to arm

2. Press ARM ALL (AWAY)

3. If a code is required, enter your code when the keypad screen appears.

The panel speaks Doors and Windows On, Motions On, starts an exit delay, and sounds exit beeps in groups of four until the exit delay expires.

Call Monitoring Station 1-855-488-3777 to advise them to ignore any signals from this device. Remove the carbon monoxide detector from the wall & cut the red wire. This will take all power away from the device. This is not recommended unless you will be replacing the device. Once the carbon monoxide detector is disabled this zone may show open on your security system – if this occurs follow the instructions on bypassing a zone or contact our office to disable the zone from your security system.

1. Enter status and Settings menu

2. Scroll to programming and press enter

3. Enter master code and press ok.

Note: You have four seconds between number presses to enter the code or you will be returned to the home screen.

To add/edit access codes:

1. From the Programming screen, press ACCESS CODES.

2. To add or edit an access code, press the white field next to the access code.

3. Enter the new/edited code on the numbered keypad and press SAVE.

4. Press CLOSE repeatedly to exit menus.

Time format is: hour/minute/a.m. or p.m.
Date format is: month/day/year:
To set the time
1. From the Status & Settings screen, select Set Date/Time.
2. Enter master access code.
3. From the Set Date/Time screen press the first box to set hour and press SAVE.
4. Press the second box to set minutes and press SAVE.
5. Press a.m/p.m. box to toggle a.m/p.m. setting.
To set the date
1. From the Set Date/Time screen press the first box in the second row to set month and press SAVE.
2. Press the second box to set day and press SAVE.
3. Press the third box and enter the year and press SAVE.
4. Press CLOSE repeatedly to exit.